Warning: session_register() expects at least 1 parameter, 0 given in /home/tiptopwe/public_html/sub-articles.tiptopweb.info/article.php on line 35
Laying Vinyl Flooring The Correct Way.

Google
TipTop Business Web Directories - Add  your sites link starting at £1


Home | Business | Ask An Expert


Laying Vinyl Flooring The Correct Way.

By: Steve Drumm

I will be blunt at this point. You’re gonna require quite a great deal of kit for this job. Unless you’ve got plenty of vinyl, it might even work out less expensive to pay for another person to do it for you.

Anyway, to do the task you’ll require a roll of vinyl (obviously), a Stanley knife, vinyl glue, a steel straight edge, a tape measure, a paint scraper (for the glue), a ballpoint pen, a roll of double-sided flooring tape. And, if you have got a tiled floor or it’s made from concrete you will probably will require some self-levelling compound.

Step 1: The Vinyl:
Laying cold vinyl is a nightmare. It’s stiff and doesn’t stretch well. So, leave the vinyl in a warm room for a day and turn on the central heating. It will make fitting it a lot easier.

Step 2: Preparing your floor:
If you have a raw concrete floor, you will need to make sure it is completely flat. Otherwise the lumps will show through the vinyl. It may look horrible and present a possible safety hazard. Purchase a self levelling compound, spread it over the floor to fill the holes and follow the instructions. That should do the trick.

Self levelling compound is what you will will want when you are covering ceramic tiles, as well. Spread a thin layer and fill in all of the joints between tiles. Again follow the instructions and let it to set.

If you are covering floorboards, you will be required to lay hardboard over them to create a flat, smooth and stable surface. Don't forget to stagger the joints and use a good amount of pins to make sure they do not lift over time.

Step 3: Lay the Vinyl:
Ensure the area is clean. Get the vacuum out and give it a top notch hoovering. Take your shoes off. You won’t need them on for this job. They will just drag grit around. Now, unroll the vinyl alongside the longest continual wall. Keep unrolling until the pattern is parallel with your wall. Leave a 4 inch overlap against the wall.

Now you will will require that Stanley knife. When the vinyl is unrolled, keep it as flat as you possibly can around the edges close to the wall by making vertical cuts into the waste vinyl (i.e. the stuff pressing against the walls that will not be covering your floor). For a neater finish, cut into the corners and trim the surplus vinyl so that you simply form a V shape.

Step 4: Fit the Vinyl:
Now that you have cut most of the excess vinyl off, it’s more manageable. Obtain a pen and mark off more excess vinyl. Cut it away. Your aim now is to get the vinyl into the rough shape of your room leaving a 1 or 2 inch excess all around the sides.

Step 5: Trim and glue:
Ok, press the straight edge against the vinyl and trim to suit exactly. Force any edges under cabinets, skirting boards etc. That will give you a decent, crisp finish. if you have got anything different to ‘stay-flat’ vinyl, this will be the time to glue it it to the floor. Follow the instructions on the glue container.

Step 6: Finishing:
You are nearly there. Using a soft brush and starting from the centre of your room, push out any bubbles. Secure the vinyl at the doors and entrances to the room with double sided carpet tape. It will stop it moving.

Article Source: http://articles.tiptopweb.info

For my training as a carpet fitter, I joined a company called Contract Flooring. It was hard going to start with but it is definitely the best way to gain experience. They taught me everything that I know.

Please Rate this Article



 

Not yet Rated

Click the XML Icon Above to Receive Ask an Expert Articles Via RSS!

© 2006-2008 Articles.TipTopWeb.Info . All Rights Reserved.
Use of our service is protected by our Privacy Policy and Terms of Service

Powered by Article Dashboard